Chevy 6.6 gas is a V8 L8T engine launched by General Motors and supports the heavy-duty Chevrolet variants. It has optimized fuel control, increases torque, provides 400 hp, and supplies fuel with quick injection.
Chevy 6.6 gas problems include low-quality transmission, malfunctioning alternators, insufficient load handling capacity, low speed, less horsepower, malfunctioning springs, additional fuel loss, and a broken time chain.
Due to the engine problems, you can hear loud ticking sounds and poor engine performance.
Low-quality transmission
A 6.6 liter V8 utilizes 6-speed transmission, which has a low performance than 8-speed and 10-speed. Its low performance affects the acceleration of a pickup truck.
The gear has slow shifting due to incorrect fluid flow under cold temperatures. In addition, due to insufficient liquid penetration in the shifter, its gears do not engage properly.
Its internal temperature rises more quickly than the counter transmissions. As a result, it has a weak configuration and overheats.
It leads to vibrations and shaking of the frame. Consult a mechanic and change the 6-speed transmission to an 8-speed or 10-speed system.
You can replace the malfunctioning sensor of your transmission by the following method. However, it is a complicated procedure and consumes around 2.5 to 3.5 hours.
Its replacement cost varies from $30 to $44 without professional assistance. For the swap, pull the negative connector of the battery source and cut the wattage penetration inside the cabin.
Approach the sensor and pull the connector. Remove the screws with a screwdriver and release the sensor from the mount.
Pull the broken electrical cord and throw them. Repair broken cords with high-quality tape.
Adjust the O-ring on the sensor and slide it inside the mount. Attach it with cords and connectors for current flow.
Readjust the connectors of the power hub and stabilize transmission.
Malfunctioning alternator and power loss
The alternator is a specific part of the truck battery which charges it. Chevy 6.6 gas has a low-quality alternator with decreased internal power.
It can consume more electric energy from the battery. However, it has a long charging time that affects the battery.
It takes more time to start the electric motor and truck. However, you can replace the problem by swapping the alternator with a high-quality option.
Disconnect the ampere flow and leave the system for stability. Hold the electrical cords and pull them.
Access the timing belt and removes it from the pulley. Next, adjust the compatible alternator, and readjust the removed components in reverse order.
Another problem is power loss due to fast driving conditions. 6.6 V8 loses the electric energy to support acceleration.
It happens due to clogged filters and contaminated injectors. You can change the mixture of air and fuel.
Use high-quality gas for the motor and upgrade the intake inlets. In addition, you can troubleshoot and upgrade the ignition unit for your engine.
Low load handling capacity
Chevy 6.6 V8 has low weight handling capacity than the counter competitors. The average capacity of a 6.6 gas engine is around 13000 to 14490.
It has 3500 to 3900 pounds less towing capacity than the diesel versions. Chevy Silverado 3500HD and 2500HD comprise built-in 6.6 V8.
They provide 400 hp with a torque of about 463 lb-feet. Their towing capacity can reach 15000 pounds to 18450 pounds.
Due to their cab styles, the latest models can tow slightly more weight with a similar motor. By increasing the horsepower of your engine, you can improve your towing ability.
You can upgrade the axle and suspension of your pickup truck.
Low-speed levels with decreased horsepower
It is a low-performance engine that undergoes several failures due to its composition. It produces a low horsepower of around 399 to 400 hp.
It has low rotations per minute that affect the acceleration of the truck. It has a reduced rotational speed of 5150 RPM.
In 2WD, it can cover zero to sixty in 9.05 seconds. In 4WD, it can take around 9.22 seconds.
The accelerator has low performance than the diesel versions. This is because you cannot change the composition of the engine and its internal parts.
For improvement, you can clean and maintain the V8. With adequate service and cleaning, you can stabilize its performance.
You can increase the acceleration by upgrading the air intake inlets. Change the filters after a specific time. Use high-quality aftermarket exhaust and mufflers.
You can adjust a high-quality tuner in the motor to regulate the speed. In addition, cleaning of the injectors can improve the production of power.
Use a supercharger to facilitate external power flow inside the 6.6 V8.
Malfunctioning springs with cranking sounds
Chevy 6.6 gas has several complaints and recalls against the cranking sounds of the springs. These are louder after the tuning procedures for the motor.
Due to a malfunctioning valve lifter, the spring produces these unnecessary noises. But, it increases during acceleration and gear shifting due to incorrect alignment of springs.
These engines require 7.5 to 8 quarts of oil for their standard performance. As a result, the springs become dry and produce knocking noises.
You can solve the problem with standard oil levels to stabilize the valve and springs. Use high-quality synthetic oil which has no internal mixing of minerals.
You can reduce their levels by adding high-quality fluids for maximum lubrication. In addition, it can remove the knocking sounds for around 13000 to 14900 miles.
Additional fuel consumption and low mileage
Chevy 6.6 gas has a low-performance V8 that can consume more fuel. They are fuel consumers due to internal force and pressure.
But, they do not provide the higher horsepower for acceleration. They have reduced mileage with low fuel economy.
A 6.6-liter V8 provides around 12 miles per gallon in the city. On highways, you can get maximum mileage of about 14 miles per gallon.
In 4WD, it provides the lowest mileage than other motors. To improve the mileage, drive the truck in two-wheel drive.
It reduces gas loss and stabilizes fuel economy. Avoid the 4WD for regular driving and protect the gas levels.
Clean and replace the fuel filters after 5000 to 6000 miles. Their replacement can slightly increase the miles per gallon of a Chevy truck.
Malfunctioning time chain and broken knock valve
GM V8 engine has a low-performance timing chain that undergoes damage. As a result, it cannot maintain synchronization between the pistons and internal valves.
Oil consumption increases due to its cracks. Lack of old flow leads to engine failures and wear. In addition, the timing belt gets off, and the heat increases its length.
You can replace it on the Chevy 6.6 gas for around $1005 to $1012. It is an 8-cylinder motor with dual valves in each chamber.
They have low efficiency due to the valve configuration. In addition, the valve lifters lack performance due to layout.
They have a shorter lifespan and require frequent replacements. However, you can improve the valve efficiency with their replacement.
You can change the broken timing belt of the 6.6 V8. The housing contains the water pump and timing belt.
Remove bolts from the alternator, tap, and remove them. Approach the crankcase and pulley.
Remove the mounting brackets of the engine and hold the belt. Detach the motor and cover by removing the bolts and nuts.
Pull it from teethes and adjust a new belt. Adjust the new belt on the tensioner, fix it on the mounts and stabilize it with side bolts.
Related Articles: