Skip to Content

How to Replace Ford F150 Blower Motor Resistor?

How to Replace Ford F150 Blower Motor Resistor?

The heat and cooling control of the Ford F150 is necessary. It makes traveling comfortable for every driver and passenger. The blower motor resisters control the fan speed. 

How to Replace Ford F150 Blower Motor Resistor? In general, you can replace the blower motor resistor of the Ford F150 by disconnecting the electric passage. Detach the old device by removal of screws. Clean its surface and adjust the new blower motor resistor with bolts. Finally, tight the device in a place and use it for fan speed controls.

The damaged blower motor resistor can cause a disaster for the heat and cooling system. The fan speed declines drastically, and the environment gets effects. 

How to Replace Ford F150 Blower Motor Resistor?

Here is a detailed guide that explains easy methods to remove and install a new blower motor resistor in your Ford F150.

Purchase new blower motor resistor

Purchase a new blower motor actuator for the replacement of these devices. Accurate size and quality are necessary for such procedures. 

Compare the new tool with the old equipment and then buy them. There is no need to invest in the wrong model because it can generate few issues. 

The adjustment problems are common due to inaccurate designs. You can also take a picture of the old device while purchasing new ones. 

It helps you to get the right design and, the process becomes convenient. 

These blower motor resistors are available in a vast cost range. They are present in online stores, and you can also get them from the market. 

Access the faulty parts

Access the old device in the Ford F150. Read the manual to locate the tool in the structure with minimum time consumption. 

These are usually present on the driver’s side. You can approach them in the dashboard compartment.

These come with a lot of electric wires. The house is a covering to protect these structures from effects. 

It also keeps the tool safe from various harmful effects. The temperature control remains stable due to such devices. Open the dashboard and each the old tool for its removal.

Disconnect its electric connections

The detachment of electric connections is necessary during such procedures. Therefore, turn off the electric supply of your truck. It reduces the chances of errors and other such accidental conditions.

The detachment of the electric wires requires pulling tools. There is an electric wire harness on the blower resistor.

The tool has a connector that can join the electric passage. Remove the connecting joint with the help of a screwdriver. 

Remove and detach the screws on the top of the heating box. It removes the resistor from this heating tool. 

Use high-quality screwdrivers according to the size and design of the screws. 

The accurate detachment allows the removal of the device properly. 

Remove the old device.

Once you have removed all the screws, the device loosens. You can conveniently free it from the connecting joints. The tool loses the workability to work in correlation with the heat box. 

The removal becomes smoother than many other methods. You can push the electric wires downwards. It keeps them safe throughout the procedure. 

This step is essential for the activity of new tool installations. Wear protective gloves in the removal procedure.

The device may be hot due to a connection with a heating device. Dislocate the tool and remove it from the original state. 

Clean its surface

There are minimum chances of any dust accumulation in such hidden parts. However, the cleaning process is necessary for its accurate installation.

Use a fiber-free piece of fabric and rub it on the surface. You can also use a cleaner in this area. Rub the cleaner cloth on this compartment. 

Repeat the prices at least 2 to 4 times. Then, leave the surface for drying conditions. There is no need to exert an amount of strength. 

These are sensitive areas, and strength can cause structural damages. 

Remove all the dust particles and observe the surface after drying.

Adjust and secure it

Adjust the new tool in the accurate area. It is also a test to check the stability and performance of such devices. 

Insert it inside the place and then leave it for some time. Then, in case of any problem, you can replace the design.

 The adjustment of the wrong design takes time to repair. It can also destroy the internal structure of the machinery. 

The test reduces frustration and keeps the system stable. Add the screws for the tightening of such instruments. Use high-quality tools for tightening the device inside the dashboard compartment.

The amount of tightness is the key factor to reduce all types of future errors. You can also take professional help in the adjustment procedure.

Install the new blower motor resistor on Ford F150

Install the new tool in the original state and adjust the additional screws. 

Use a screwdriver and tight the device in the spot. Hold it and then check its movement according to stability conditions. 

The connection of an electric wire harness system is essential. First, attach the connector of the harness and then tighten it. Keep the movements clockwise until you hear the sound of a click. 

It provides information about the adjustment of the screws and connectors in one place. 

How much does it cost?

The average cost of the process is around $115 to $130. The labor cost is approximately $45 to $60. The screwdrivers cost around $17 to $45. 

The protective gloves are around $15 to $23. The average cost of total equipment in the process is approximately $69 to $71. 

11 Examples of Ford F150 Blower Motor Resistor with their size, weight, and price

  • Dorman Blower Motor Resistor for Ford – 3 x 4 x 3 inches x 2 ounces – $16
  • HVAC Blower Motor Resistor – 3 x 4 x 3 inches – 3 ounces – $18
  • HVAC Blower Motor Resistor Replacement for Ford Expedition – 4 x 3 x 2 inches – 3 ounces – $19
  • FAERSI HVAC Fan Blower Motor Resistor – 4 x 4 x 2 – 2 ounces – $21
  • Motorcraft HVAC Blower Motor Resistor – 5 x 4 x 4 inches – 4 ounces – $61
  • Motorcraft YH Blower Motor Resistor – 4 x 3 x 4 inches – 1 ounce – $23
  • Dorman HVAC Blower Motor Resistor – 3 x 4 x 5 inches – 6 ounces – $25
  • Dorman 973 HVAC Blower Motor Resistor – 5 x 4 x 3 inches – 4 ounces – $18
  • BOXI HVAC Blower Motor Resistor – 4 x 4 x 3 inches – 6 ounces – $54 
  • TTIIHOT HVAC Blower Motor Resistor – 4 x 4 x 2 inches – 5 ounces – $49
  • A-Premium Blower Motor Resistor – 5 x 3 x 2 inches – 3 ounces – $52

Related Articles:

How to replace the fan clutch on a Ford F150?

Can you replace the door lock actuator on a Ford F150?

How do you remove the cup holder in your Ford F150?