Skip to Content

How to Remove Ford F150 Cup Holder?

How to Remove Ford F150 Cup Holder?

The cup holders in Ford F150 are beneficial to support the holding material. These are of plastic material and enhance the appearance of the dash section. 

How to Remove Ford F150 Cup Holder? In general, you can remove the Ford F150 cup holder by disconnecting the electric power supply and remove its cover. Next, insert a sharp edge screwdriver and detach the clips. Finally, pull the cup holder and remove the electric wiring. 

How to Remove Ford F150 Cup Holder?

Here are 5 easy steps to easily remove the cup holder in your Ford F150. 

Turn off the engine and battery of the Ford f150. It instantly cuts the electric power supply off for the removal procedures. 

The presence of electric current can lead to various problems like short circuits. Therefore, it is not beneficial for the performer and can lead to life-threatening incidents. 

Turn off all the electrical passages to this device. Allow the tool to cool down for at least 5 to 10 minutes. Never touch the cup holder directly from the electric wire system.

Access the cup holder

The cup holders comprise the covers that hide them inside the dashboard area. Therefore, they remain safe under such compartments from the external effects.

The surrounding system remains non – affected due to the internal configuration of the holder. The cups are usually two, and they have plastic material.

Both of them remain attached in one system. Therefore, the detachment of the cup holders is not necessary during such removals. 

The covering of the cup holders is like a door. Remove the cover manually without inserting any tools. 

Observe its attachment pattern with the backside of the dash area.

It stays in one position with the clips and metal structures. The attachment remains secure in one spot. The connection is vulnerable, and you can detach it comfortably.

They require proper tools for their removals. You can get the available instruments for such detachments. 

Adjust the pulling tool

Use the pulling tool like a screwdriver with a sharp edge. 

Insert the tool on the sides of its cover. There are multiple clips of the adjustments. The sides remain secure due to supporting tools.

Insert the screwdriver and detach the clip. It loses the system from one edge. There are at least 4 to 6 clips in such structures.

Push the inserting tool and then pull the cover. Next, detach all the relevant attachment tools. Finally, stabilize the cup holder with the help of hands. You can also take the support of a friend or family member during such activities.

Detach its clips

Detach and remove the backside clip with the help of a screwdriver. The pushing becomes convenient due to such sharp tools, and they can separate the clips from the metal section. It remains stable until the person removes them.

You can also keep the clip stable with the device. The removal activity depends on the future needs of the user. 

In few cases, the user discards the attachment clips from the device. Thus, it provides control and stability to the installation activities. 

Use hands to pull it

Move the cup holder by detaching the supporting tools. Keep them on one side if you want to use them in the future. 

Use hands during such removal procedures. Never exert an excessive amount of strength because it can lead to breakage of the instrument.

The removal becomes challenging when it separates into two halves. Next, pull it by inserting fingers inside the holder. 

Adjust on the sitting area of the truck and then grab it. Keep the directions in forwarding ways and then exert strength.

Keep pulling it until you get the device in your hands. Keep the movements gentle and then pull them outwards. 

 Remove the cup holder

Remove the cup holder from the dash section. You may find a network of electric wires behind the device. 

Use a wire puller in such activities and then push them downwards. Disconnect the electric wires from the connecting joints. 

Push them downwards to protect them from breakage. In addition, it secures the system from various electric issues. 

Hold the device manually and cut the backside connections. Then, you can detach it completely and can handle it thoroughly. 

Make sure the device is not dwelling during removal activities. A sudden fall can also lead to damages to the cup holder. 

Why would you remove the cup holder in a Ford F150?

Multiple reasons lead to the removal of the cup holder in a Ford F150. 

Broken cup holder

These are of plastic material, and they become vulnerable with time. The damages and cracks can occur on the top side of the device. In addition, the parts of this device shred, and it leads to removal procedures.

People do not like the broken devices, and they select instant procedures to remove such damaged tools. Therefore, it is a significant cause of such removal methods. 

The damages can lead to the complete tearing of the plastic device. 

Molding

The high level of temperature has a direct effect on the nature of the cupholder. The internal heat also leads to the melting and molding of the structure. 

It leads to deformation of the structure, and it cannot hold a cup. Therefore, the system also becomes vulnerable due to deformation.

It can suddenly break into different parts after such high heat conditions. 

Faulty bulb

There is a bulb inside the cup holder of few designs. Unfortunately, the bulb can burn out due to age and other such problems. In addition, the heat can lead to the sudden breakage of such light tools. 

Damaged cup holder cover

A cover is an essential tool for its security in the dash area of the truck. However, it can break down due to external force. 

An accidental situation can also lead to the breakage of such instruments.

12 Examples of Ford F150 Cup Holders with their size, weight, and price 

  • F-150 Cup Holder Insert – 7 x 6 x 6 inches – 10 ounces – $28
  • Red Hound Auto Cup Holder Insert Holds 2 Cups – 9 x 4 x 3 inches – 7 ounces – $37
  • Red Hound Auto 2 Rear Cup Holder – 4 x 2 x 5 inches – 5 ounces – $32
  • Red Hound Auto Console Cup Holder Rubber Inserts – 10 x 5 x 9 inches – 7 ounces – $29
  • Winunite F150 Cup Holder Insert – 11 x 6 x 5 inches – 3 ounces – $28
  • Winunite cup holder – 8 x 9 x 5 inches – 3 ounces – $28
  • Dorman Cup Holder – 3 x 8 x 10 inches – 5 ounces – $30
  • Red Hound Compatible Cup Holder Rubber Inserts Liner – 6 x 4 x 5 inches – 4 ounces – $25
  • Cup Holder Insert Holds – 10 x 5 x 4 inches – 4 ounces – $14
  • Ford Tan Cup Holder – 14 x 4 x 12 inches – 3 pounds – $20
  • Ford Genuine cup holder – 11 x 11 x 6 inches – 3 pounds – $45
  • BottlePro – Adjustable Cup Holder – 6 x 5 x 5 inches – 8 ounces – $45

Related Articles:

Can you remove the back seat in a Ford F150?

How to install a blow motor resistor in a Ford F150?

How to remove overhead console in Ford F150?

How do you remove the Ford F150 center console?

How do you remove air vents in a Ford F150?