Here are 4 easy steps to remove and add a new front brake caliper in your pickup. It is an easy process; just follow the guidelines mentioned in this article.
How to Replace Front Brake Caliper on Ford F150? You can replace the front brake caliper on Ford F150 by using a clamp and remove the screws, nuts, and bolts, open the brake line, remove the brake, clean the area, and put the new brake caliper.
How to Replace Front Brake Caliper on Ford F150?
Move the front area of the vehicle using lever and jack. The upward movement should be accurate and enough.
The stand helps in the machinery’s stability to not fall on the person below the truck. You can put all the vehicle’s weight on one side of the vehicle with the help of a stand and then stand it on this jack.
You can perform this step by two methods, one of that involves replacement and flexibility.
Remove the brake lines
Use a clamp that is in C form, and it is vital. Adjust the clamp and pinch it in a way that it adjusts completely.
This process decreases the amount of fluid, making your hands and clothes dirty in the form of a spray.
These tools are flexible, and these are removed after every five to ten years. These should be removed after visible cracks and damages.
After removal, places the lines on one side and make sure they are secure from dirt and dust. Use a pan for catching this area, which surrounds the gadget. In this method, the fluid rushes out of the vehicle.
Lose it from the central point and keep on doing this until completely loosen. Do not use the adjustable wrench for performing this function. You can also remove the parking brake cable on your pickup.
Use a wrench of adjusted size, and it should be strong in its nature and quality. A standard wrench removes these easily without removing the fluid from the vehicle. You can do this if your vehicle is in the limp mode.
Unfasten the fitting of the vehicle; use a pen cap or other such material. Adjust it inside the area and pull it towards you.
Remove the brake caliper
Find out the fluid removing the nut on the backside of the old brake and its caliper.
The screw contains a cap, which is rubber in the material; it protects the screw. Use some pliers to loosen the strength of the rubber cap over the screw.
Remove the cap in such a way with little effort and power. The procedure results in the removal of fluids that stick inside the device.
Use screwdrivers of different sizes and start losing the screws which keep them straight and stable.
It is essential to remove it, but you cannot do this without removing all the parts. There are some pins on the machinery use screwdrivers to remove them.
Remove all the screws and bolts, keep all the things aside carefully if you want to use them again. It must be done carefully, otherwise, it can cause your truck brakes to lock up.
Put new brake calipers
There is some equipment which is placed on the new equipment. These are known as pistons; before installing these parts, make sure that these pistons are entirely closed.
Moreover, compress the piston so forcefully that the spring should move a bit high than its normal strength. If you are not following the procedure carefully, then pistons can be damaged, and they start dragging themselves.
Now install the new pads inside the calipers of the vehicle. These should be installed carefully by thoroughly analyzing the area of the pickup.
Adjust the new tools on the surface of the rotor. Insert all the pins and nuts and do mot tight them immediately. A little insertion is enough for making a complete rough sketch.
Clean the rotor and other tools by cleaners of your choice. Do jot spray or put the cleaner directly. Dampen a cloth in the liquid cleaner and remove all the dirt and dust.
You can also spray the cleaner on the rotor by slowly and frequently moving the tool in the opposite direction. These cleaners tend to dry fast as compared to other vehicle cleaners.
Attach the tools at the backside, you have to attach every single part which you have removed in previous steps.
Bleed the truck brakes
Start bleeding and flushing phase after installing a new device. There are four calipers of brakes inside the pickup. You need to bleed and flush the machinery either you add one or four of them.
The process is carried out to identify that there are no air bubbles inside the machinery and their tools. These are hydraulic in nature, and bubbles of air stick inside them.
Bleeding is a process that should be performed simultaneously. You cannot bleed on the side at once and then the others. Make sure that all of the parts are working together.
Related Articles:
Can you replace the brake master cylinder on Ford F150?