Radio is the type of infotainment system in a Ford F150 truck and is your best partner while traveling alone. You can get rid of boredom by turning it on and listening to your favorite music while enjoying the trips.
Why is My Ford F150 Radio Not Working? Ford F150 radio stops working due to faulty speakers, moving in remote areas, disturbance in solder flow, electric issues, and antenna problems. In addition, it happens due to a frozen radio system, poor installation, software glitches, and a blown-out fuse.
It is frustrating when the radio becomes stuck at one point and does not work. However, you can also replace them and install the new one as an aftermarket addition if the old one gets damaged and is not repairable.
|Ford F150 radio problems||Solutions|
|Speaker issues||Remove dust from speakers|
|Antenna and satellite issues||Use signal boosters and extenders|
|Disturbance of Solder flow||Heat the mainboard to resolder the joints|
|Frozen radio system||Resent the radio system|
|Installation issues||Check the connection of wires|
|Software glitches||Update Ford Sync|
|Electric issues||Replace blown-out fuse and damaged wires|
You can see the display but do not hear any sound because of faulty speakers. The speakers blow out when you continuously listen to music at high frequency.
Driving on bumpy roads and high vibrations affects the thin cables of the speakers. The frayed cables cannot supply power to these components, and you do not hear any sound.
The dust also accumulates on their exterior surface and interrupts their functioning. The issue also comes when you frequently change the frequency of sound.
Resolve the problem by checking the fuse of the speakers and replacing the blown-out ones. You can also change the speakers completely if these are defective.
Removing dust and dirt using a dryer and vacuum is also better. Moreover, do not frequently change the intensity of the sounds because it can increase blowout chances.
Antenna and satellite issues
The radio receives signals from specific satellites and produces sounds when both of the waves match with each other.
Distortion in sound produces when you are moving away from these satellites. Many people complain that they feel the distortion in sound when traveling in remote areas.
The issue comes in rural areas because of fewer signals there. Sometimes signals also get completely blocked when moving away from the satellites.
The antenna also gets damaged during deep washing procedures, or water entry makes them faulty.
You can fix the issue by driving your vehicles in the areas so they can easily catch the signals from the satellite. In addition, you can use extenders and boosters to increase signal strength.
Take your vehicle to authorized workshops for deep washing and protect its components from damage.
Disturbance of Solder flow
Solder joints are in the electric circuit, which are shiny metal materials to keep the wires in their places.
Moreover, the current flow through these joints and turn on the radio. The disturbance in these solder joints causes malfunctioning of the components, and you cannot hear sound.
Solder joints get damaged due to high vibrations during driving. Moreover, the problem also occurs due to overage and frequent use.
The stress on these joints causes their disruption and hindrance in electric flow. The problem in metal joints comes due to temperature changes.
You can fix the issue by removing the main board to resolder the joints. Then, take a piece of cardboard and cut it into the exact dimensions of the mainboard.
Preheat the oven to 380 to 385 Fahrenheit and put the mainboard and cardboard on its lower side.
Leave it for 5 to 7 minutes, then place it outside for cooling before its reinstallation in the Ford F150.
Frozen radio system
Frozen radio is a common problem, and people face this in new models of Ford trucks. A frozen system means the sound gets stuck at a single point and does not move forward.
In addition, it occurs after a few days, and the system starts working fine. The issue comes due to the overloading of the operating system or a bug in it.
The system becomes irresponsive in that you can see the display but do not hear any sound from the speakers.
The frozen issue comes due to a poor connection between the magnetic base and the cone membrane of the speakers.
The device does not shut down suddenly but causes hindrance in sounds. You can fix the issue or remove the error by resetting the procedure.
Press the power and right seek buttons simultaneously and wait for 12 to 14 seconds. You can also reset it by disconnecting the battery if the problem persists.
Disconnect the battery’s negative terminal and wait for 20 to 25 minutes.
The incorrect installation of radio as an aftermarket addition in the Ford F150 also makes them faulty. In addition, the connection of the wires is not accurate, which causes hindrances in their functioning.
The issue comes when you hire inexperienced mechanics for their installation or do the procedure at home without having enough knowledge.
The attachment of the wrong wires can also damage the radio components completely. Sometimes, the mechanics install it correctly, but the connection of cables is not accurate.
It is better to hire experienced experts for their installation. Check the wires connections after installing them before turning them on.
The software issue comes when you do not update the Ford sync that is essential for working the infotainment system.
The old version does not support your vehicle, and you cannot enjoy the stereo or infotainment features. This will also cause problems with its display screen. Therefore, it is better to check the updates regularly to get rid of any problems.
Turn on the touch screen and also connect it to the Wi-Fi signals. Next, log in to your sync account, open the settings menu, and select the automatic update option.
Scan the system to find the new updates and install it if it shows the latest update.
The radio in your truck does not work with a blown-out fuse. The fuse is the electric component that protects your device from the power supply surge.
The fuse for this is also in the box to protect them from malfunctioning and surge of power supply.
They blow out when extra voltage comes in their way and becomes dark brown in color. The blown out also comes when you overload the electric system in your vehicle.
Fluctuations in voltage also make them faulty and increase the chances of a blowout. You can face the issue due to overheating of the components.
It occurs due to overuse of the radio during driving without any gap. Wires also get damaged, and their connections become loose, causing an interruption in the flow of current.
The two fuses of the radios are present in Ford trucks. One is on the engine bay side, and the other on inside the passenger cabin.
The two fuses are present because the amplifier has a separate one. Therefore, checking both of them and replacing the faulty ones is essential to fix this issue in Ford F150.