Roll coal in trucks requires two primary components: right fuel and engine type. Diesel fuel gives more black, thick, and sooty exhaust fumes.
However, emission from the exhaust tailpipe on purpose is a harmful act that violates air clean regulation.
How to Make Your Truck Roll Coal? You can make your truck roll coal by installing a large injector and smoke switch. Then, remove the catalytic converter that is a less time-consuming process. Another easy and less expensive technique is the engine modifications like ignition timing alteration and using the tuner.
However, it harms the environment, human health and causes engine wear and tear issues.
For roll coal, you must consume the proper mixture of air that helps in the combustion of your vehicle fuel.
- 1 How to Make Your Truck Roll Coal?
- 1.1 Use Large Injector
- 1.2 Truck Engine Modification
- 1.3 Smoke Switch installation
- 1.4 Remove Catalytic Converter
- 1.5 Truck Pulling
- 1.6 Is Rolling Coal bad for my truck?
- 1.7 How much does it cost to Roll Coal my truck?
How to Make Your Truck Roll Coal?
White, blue, and black are some of the colors of diesel engine smoke emissions.
Black smoke is produced in the case of high acceleration that is a sign of poor engine performance, a rich mixture, or a lack of oxygen that leads to incomplete fuel combustion.
It is a leading source of climate change or global warming and more poisonous air pollutant. The discharge of toxins from it causes around 15,000 deaths every year.
It is emitted in various ways, either intentionally or unintentionally.
With time, there is a lot of advancement and modification introduced in the truck engine by the automakers.
Roll coal is a deliberate modification of your truck engine or another element of your vehicle. In this case, the high amount of fuel transmits to it can result in incomplete internal combustion.
This variation can lead to the emission of black smoke. There are several approaches you can adopt to perform this activity.
Use Large Injector
The primary purpose of the injector is to spray the diesel in mist form.
As a result, it may pour sufficient gasoline whenever you need it during each injection cycle. Fuel enters the injector either through the top known as a top feed.
The next which common is the side-feed. It can lead to the delivery of more fuel against more throttle. Run upper fuel injector to compensate more fuel.
Generally, fuel injectors regulate the fuel spraying, proper timing, and other parameters. For the proper working, it needs fuel injection at an accurate time.
Injection metering is also typical in this situation to satisfy the appropriate need.
Truck Engine Modification
Engine tuner is essential from which you can determine and control the fuel quantity.
You can buy these, and the purpose of the owner may vary. For example, some want to spew black smoke to get the best engine performance, while others adjust it according to roll coal.
You can buy it online, and its installation and adjustment are easy for you. Ignition timing also alters by the software update and computer chip.
Smoke Switch installation
You may program the smoke switch to enhance more fuel consumption by fooling the engine sensor can lead to roll coal or release out of black smoke from the exhaust tailpipe.
The primary purpose is to increase the voltage or power that moves toward the data sender cable. First, it indicates the engine system that your truck is working at high pressure. Then, you can install it in few steps.
First, determine the location of the switch on your choice. The most preferable is under the steering wheel or another accessible place for installation.
It requires fuses, 16-gauge wire, a fuse holder, a toggle switch with two prongs on the rear, and other additional components. Finally, you lift the engine cover after ensuring that the engine is cool.
Next, disconnect the stock and chips map sensor from it. Make sure the toggle switch may not connect to the ground wire and secure with the electrical tape.
Remove Catalytic Converter
The catalytic converter is the best thing in your truck that converts the harmful component or chemicals into harmless gases like steam.
The new advanced truck equips with the best quality catalytic converter. People want to get more torque and horsepower. It is illegal to remove it because it reduces the performance and effect on mileage too.
It also reduces the EGT, and it takes almost less time, approximately 25 to 28 seconds. Finally, it is either connected through the bolt or weld.
You have to unbolt on both sides for removing. Then, cut from both sides of catalytic converter pipe.
Truck pullers can also modify their vehicles for the rolling coal. It occurs when people compete in contests to see whose truck can haul the most load and emit the thickest black smoke.
People take more interest in truck pulling, and many associations involve an organized event like Tractor pulling association and others.
They have many members in the association that participate in the competition. These associations take utmost care and have top priority related to safety and the surrounding.
Is Rolling Coal bad for my truck?
There are several disadvantages related to rolling coal activity for trucks.
Wear and Tear Issue
Although this phenomenon increases power, but also harms your truck engine, like wear and tear.
It can cost you almost $550 to $650 for modification.
The tuner can modify your engine, but it affects the transmission, gears, and coolant system.
It has a significant harmful effect on the environment and human health.
The serious adverse effects produced by it include respiratory problems. In addition, according to some association reports, lung cancer risk increases with long-term exposure to black smoke.
It also affects the visibility of other driving people, and you are unable to see clearly for a few minutes until things become clear out. It also enhances the risk of road accidents.
The United States Environmental Protection Agency (EPA) has declared it unlawful to violate the Clean Air Act to discourage this activity among motorists and others. Moreover, each state has its own rules and regulation in the case of roll coal.
For instance, if you break this law in Colorado, you can be in prison for 30 days and fined up to 1000 dollars.
In California, roll coal is also an illegal act. However, if you belong to another state, you may get a ticket to violate the law.
This action is now forbidden in Maryland and charges a fine of more than $450, but diesel vehicles with acceptable exhaust emissions have no restriction.
Furthermore, If anybody tries to change or modify the emission, then on average penalty of $4500 to $5500 impose in violation of the law.
Lead to Aggressive Driving
It can result in more aggressive driving to enhance engine performance and the emission of black smoke from the exhaust.
However, it can lead to some drawbacks like high accidental risk and impair the vision.
How much does it cost to Roll Coal my truck?
Investment in this regard varies depending upon the quality of work and engine size of your vehicle. For this modification, you need a high investment for the efficiency of your truck.
The cost of roll coal is approximate $600 to $4500. Out of this amount, around 500 dollars require for mere plug-in modification.
The rest of the amount goes for smokestacks addition and modification of smoke switches.