Skip to Content

How to Install Mud Flaps on Ford F350?

How to Install Mud Flaps on Ford F350?

Here are the 12 best DIY methods for adding mud flaps to your truck. They not only use to save your pickup from dirt but also rocks, hazards, ice-melting chemicals, dirty water, corrosive substances, salt, weather condition, and much more.

How to Install Mud Flaps on Ford F350? You can install mud flaps on your Ford F350 by measuring their size, clean the surface, remove the wheels, drill the holes, disconnect the fasteners, attach the splash guards, and secure it with screws.

These act as a barrier to defend the paint. Some people consider mud flaps are not essential tools, but they work surprisingly.

How to Install Mud Flaps on Ford F350?

Installing mud flaps on your pickup is the simplest method. You need to follow the guidelines that are given in the instruction manual.

Tools required

  • Spring clips
  • 6mm bit drill
  • Mounting screws
  • Philips screwdriver
  • Wrench kit
  • 10mm socket
  • Protective sunglasses
  • Rubber gloves

Read and follow instructions manual kit

Specific model vehicles might have a different manual kit and may use other methods because some vehicles are manufactured different from most trucks.

It is better to check the given instruction book before beginning the process. The instruction book thoroughly guides you with a diagram.

You should follow step by step method and should match your tools and parts with that. By following directions, even an inexperienced person can complete this within minutes. You can replace a starter on Ford F150.

Use stainless steel mud flaps

There are two kinds: sheet metal and rubber. Both will work to saves your vehicle and rig from dust and debris.

Stainless steel is more decorative, durable, and long-lasting. Before choosing the product for your pickup, keep it in your mind, never purchase plastic or rubber accessories.

They will not work correctly and unable to clean the wheels. Always use stainless steel or anti sail weight splash guards.

These assist in away the dirt and keep splash guard integral. They avoid flying while the vehicle running. If it flies off, the dirt and rubbish will make them dirty and damage or make scratches. Use good quality tools, if you are using 4 wheel drive on your Ford F150. then use good quality tools.

Measure the size

Usually, these come in diverse sizes for different models for the rear and front tires. You should check the correct position and then fix them.

These are available for the right-hand and left-hand marking. The left side accessories can be attached to the driving seat side of the pickup. You can also reset the ABS lights on your pickup within a few minutes.

Clean the surface and wheels

You should clean the area and wheel properly to prevent dirt, debris, tar, and dust. The clean surface will save from scratching after they are attached.

Clean the wheel with soft clothing. Dip this cloth in water and add a few drops of cleanser. Thoroughly clean the area with this cloth well. You can use it for removing the windshield wiper arm on your pickup.

Left it for 10 minutes and then wash the fabric with tap water and troll this cloth gently to clean the cleanser. Left it for a few minutes and let the wheel dry.

Park the truck on an even surface

Park you pick up on a level floor and the tires can turn quickly to full right to left and left to right.

The main benefit of the level surface is it helps to put flaps on the right place or proper location.

Remove the wheels

Before adding these accessories, you should remove the tires first. Disconnect the tires of the pickup will give more space to connect the tools.

It also helps make your process more manageable, comfortable, and saves your hand from any damage or harm.

It is not an essential task before beginning the procedure, but you can do for better result. Removing the wheel is only recommended for those people who are expert, experienced, and professional.

Male sure you are wearing sunglasses to protect your eyes from dust and dirt. You should also wear gloves to save your hand from germs and cut by using different tools.

You should choose the correct gloves, should use rubber gloves. You can move your fingers and hands properly after wearing gloves. Make sure your gloves do not act as hurdles in your work.

Work in an open space

Before starting the entire process, you should find the best space to work adequately. You should park your vehicle in a smooth, open, and large area.

Never choose the small area; it will hinder to connect correctly. You can stretch out or move comfortably and contentedly.

Drill the holes

Most vehicles and different models have come with drilled holes for mounting these products. Most pickups have no pre-existing drilled holes for their connection.

These are required to drill or make holes as you need. Before drill holes, you should check the size of the screws and bolts.

Drill the holes on the pickup frame and take them as a model. Make holes carefully and slowly according to accurate size. First, drill one hole as a test and connect screws to check the size.

Now make all holes with the help of a drill machine, take care that all holes are on an exact level with the leading one, then fix screws and nuts.

Disconnect the fasteners

First, identify which fastener use to help on the plugs for your splash guard. After recognizing fasteners, remove them by using a ratchet set or screwdriver.

Make sure you are keeping these bolts, nuts, screws, and washers on the safe place.

Attach the mud flaps on Ford F350

To add these on the driving side and first passenger side. Disconnect the pin A by spinning bonce to the left 1/4 rotate and tweak.

Disconnect the bolt and screw B. Put the plastic supplement, available with the set. Now mount these, and they should be corresponding to the ground and align them at your preferred height.

Locate holes in the side bumper, connect plastic supplement in the slum. Place them and secure the screws, bolts, and nuts with the wrench.

You should not tighten the screws and bolts because you might be reuse washers and screws from your automobile. If you need the extra hole, drill them, many holes and screws will help you enhance the strength, power, and reliability.

Tighten the screws properly

Before tightening the screws, you should check their angle and position. Take care that the tools are aligned vertically and fix correctly.

If these have extra holes, and your vehicle does not have spots to enter these screws. You can drill new holes to increase stability.

Tighten all screws and bolts by yourself with the help of a wrench. They should not be over tighten and feel comfortable.

Benefits

Create a barrier between the wheel and tires: The most beneficial for people who live in a rainy or snowy climate.

These are also helpful for those people who live in a grimy, desert, or sandy area. They are best when you have to travel on gravel or stony roads.

You can spend this saving on pickup maintenance in the future and make your vehicle brand new ford.