Here are the best DIY methods to reset the ABS light on your pickup. You can do all these steps at your home, just follow this step-by-step guide.
How do you Reset the ABS Light on a Ford F150? You can reset the ABS light on a Ford F150 by disconnecting the power supply, replace the light sensor, reset the module, and refill the brake fluid reservoir. You can use scan tools to read the error code and fix it.
How do you Reset the ABS Light on a Ford F150?
It is called the antilock brake system light, and it is mostly present on the vehicle’s dashboard. When this light gets on, it is an indication that there is some problem in the vehicle.
It prevents the locking of the wheel when you suddenly push the brake pedal in an emergency.
Disconnect the power
In this method, you need to disconnect the power supply for some time. First of all, park the vehicle in a safe place.
Then wear rubber gloves for your safety. you will also require an ignition key, a wrench, and a socket.
After this, take the ignition key and put the ignition on the on position. Then you have to locate the battery and its negative terminal.
Open the hood of the vehicle and locate the terminal with black color or negative sign. Take a wrench and disconnect the clamp of the negative terminal from the battery.
Then wait for 5 to 10 minutes. After this, again connect the negative terminal clamp with the battery and attach the clamp’s nuts with the wires tightly. You can also change the starter of your truck to fix it.
Change the ABS light sensor
These sensors are the main component of this device. These sensors sense and measure the rotational speed of the wheels of the truck.
These sensors find out which wheel is going to lock and sends information to the engine control module.
The module then hinders or prohibits the wheel from getting locked. Sometimes faulty sensors are the main reason for the malfunctioning of the tools. So for this, we need to change the sensors.
Changing the sensor is a difficult task. First, raise the front of the vehicle with a jack stand and lose the wheels’ lug nuts.
Then pull the wheels away from the truck. Then locate the sensors which are usually present at the suspension of the vehicle.
Then take a ratchet to unbolt the sensors from their place. Take a long tool to reach the bolts properly.
After unscrewing all bolts, remove the sensor. Clean the sensors and check their wiring. When the wiring and sensors are worn out, then replace them with a new one.
Screw the bolts again and put the wheel in its place, and tighten up the lug nuts.
Reset ABS module
Sometimes the fault in the ABS control module is the main culprit. To adjust this, you should reprogram it or replace the whole system.
If the control module gets corrode, and it causes difficulty in sensing the wheel speed or may cause a delay in data transfer to the central power unit.
To replace it, first, disconnect the terminals of the battery. Then disconnect the wires of the modules.
Here are two types of cables. One is connected to the central power module unit, and the other is connected to the sensor to transfer data from wheels to the control system.
Take a screwdriver to unplug these wires. Unbolt all the bolts that are holding the Controller module in the pump motor.
Now take the new control module, and it should be identical to the old one. Clean the new module with a clean cloth and place it in its respective location. Tighten up all the bolts carefully and again connect the connectors with the control module.
Refill brake fluid reservoir
When the brake fluid is low, it suffers from the issue, so you should also inspect the brake fluid reservoir.
Brake fluid is also called hydraulic fluid. It transforms the force into pressure to make the brakes work.
When they are low, the brake cannot work correctly, and the vehicle stops unexpectedly. Refilling and changing the fluid can solve the problem. To do this first, you should locate the reservoir.
Before start working, raise the vehicle and locate the master cylinder. Remove the cap of the cylinder and check the level of the fluid. You can install new mud flaps on your Ford F350.
When you feel it is too low, add the required amount of it in the cylinder. You can also replace it with new brake fluid.
First, withdraw all the fluid using a vacuum pump. Then add new and fresh fluid up to the mark. Again screw the cap on the cylinder. You should also replace the fuel filter on your truck on regular basis to prevent any further issues.
Use a scan tool
These gadgets can have faulty codes in the central unit, these can appear in the computer display when there is an error. First, turn off the daytime running lights on your truck.
On average, there are around 40 different codes that show these issues. By reading the fault code, you can know the actual cause of the problem.
Other types of code readers are available at the market. You can buy any of them to read the error.
Connect the scan tool to the computer system of the pickup. Then read the error code. There are half of the error codes related to wheel sensors issues, it can be solved by changing the front rotors on your pickup.
Why do you need to reset the ABS light on your truck?
This light serves as a diagnostic tool for various problems. When we start our vehicle in normal conditions, it turns on for a short time and then turns off.
When it remains on or does not gets on, it is an indicator of an issue. When there is a fault or has blown its fuse, it stops working.
It means that it can not warn us of the problems with the vehicle. It is so much risky to drive when these are not working.
To solve this problem, we need to adjust them correctly. Continuous and time-to-time maintenance of them are essential for both trucks and drivers.
Related Articles: